#Error code 3259 outlook 2011 installOnce you have quit Outlook in step 4 at that link in the previous step, start Microsoft AutoUpdate and install all available updates until you Office is updated to 14.2.4.Ģ1. (and there you go, all your data back in front of your eyes….with all the folder structures maintained)……BUT HOLD ON, you’re not done yet.Ģ0. While you are still disconnected from the internet, start Microsoft Outlook. You should receive a message saying that your database was rebuilt successfully. Otherwise, it would just be a waste of your time because the rebuild will probable fail).ġ7. Now click Rebuild and keep your fingers crossed (that’s of course only if you have enough memory as explained earlier. Now launch the database utility, and you should only see that duplicate of your corrupted identity. Delete “Identity 1″ from the location mentioned in the previous step (you won’t need it anymore) and then move the duplicate of your corrupted identity in its place.ġ6. What you intend to do here, is trick the database utility v14.1.4 to think that your SP2 identity conforms to its own version and will then attempt to rebuild it.ġ5. What you have done now, is copy a clean “Database Headers” folder that has database headers in version 14.1.4. Now copy the “Database Headers” folder from “/Documents/Microsoft User Data/Office 2011 Identities/Indentity 1/Data Records” and paste it inside the “Data Records” folder of the duplicate of your corrupted identity. Then navigate to the “Data Records” folder and delete the “Database Headers” folder.ġ4. In the duplicate of your corrupted identity (created in step 1), delete the database file. It will automatically be named “Identity 1″.ġ3. Now that there are no identities in the list, create a new blank identity. DO NOT DELETE IT if it is there (you must have done something wrong….start over).ġ1. Your corrupted identity should not appear in there. Open the Microsoft Database Utility, and delete all the existing identities. Disconnect your computer from the Internet and do NOT reconnect it again until you have completed the recovery.ġ0. #Error code 3259 outlook 2011 updateManually download and intsall update 14.1.4 from. Open a blank document in Microsoft Word, and allow it to fully load up. Make sure that you do not install any later updates than that.ħ. #Error code 3259 outlook 2011 upgradeLaunch Microsoft Auto Update and upgrade Office to SP1 14.1.0. Install the original Office 2011 14.0.0 onto your computer, and make sure it is activated.ĥ. Use the instructions at to completely remove all Microsoft Office from your system.Ĥ. Make a duplicate copy of your data to work with and keep your original corrupted identity safe in case this method of recovery doesn’t work for you.Ģ. If you wish to rescue your folder structure, read the steps below very carefully and try to follow them precisely and hopefully you will be able to recover your data.ġ. By the way, these memory constraints apply to both of the recovery procedures the one described above and the other one described below. Otherwise, you would just be wasting your valuable time. #Error code 3259 outlook 2011 freeSo, I would recommend that you make sure you have at least 300GB of free space on your hard disk and at least 8GB of RAM installed. (WIERD BUT VERY TRUE) I also did notice that during the rebuild, my computer was using about 6.8GB of RAM. I freed up even more space and tried again with 310GB of free space on my hard drive, and that succeeded to build. And so I freed up some space and tried again with 200GB of free space on my hard drive, but that failed too. It even failed to rebuild a non-corrupted identity. My database is 12.7GB and I had 120GB of free space on my hard drive, but that failed to recover. One thing to keep in mind though, before I start explaining the second recovery method, is that memory is the key to recovery. If you don’t share my problem of having to recover the folders named and organised and sorted, and you just need your messages back, then this first solution would be easier for you. In fact, in my case, it would almost be impossible. When my data was recovered in this manner, I had 558 folders at the top level all named “Recovered Folder 1″, “Recovered Folder 2″, “Recovered Folder 3″, etc… Obviously, it would be a nightmare to try and rebuild that hierarchical structure again. I had 10 folders at the top of my hierarchy, with loads of subfolders inside subfolders inside subfolders etc… In total the number of folders I have is 558). This will result in you being able to recover all of your data, but you would lose all you folder names and hierarchical structure. The first way is basically following the instructions at -restoring-and-upgrading-fails/, however, with the following modification.ĭo NOT copy the folder “FOLDERS”, but copy “CATEGORIES” instead. There are two different ways you can recover your data.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |